1. The feeding and mixing machine should not be repaired and lubricated during operation.

2.定期在每个润滑脂嘴上添加黄油，并在轴端密封处每4小时润滑一次油，每周排水一次。

2. Regularly add grease to each grease fitting, lubricate the shaft end seal every 4 hours, and drain water once a week.

3.使用上料搅拌一体机后，根据需要在每个润滑点添加必要的润滑油（滚筒轴，滚筒，钢丝绳和其他有效部件）。

3. After using the feeding and mixing machine, add necessary lubricating oil (drum shaft, drum, wire rope and other effective parts) at each lubricating point as required.

4.上料搅拌一体机减速机的齿轮和轴承使用齿轮旋转将油溅入油箱内壁并流入轴承进行润滑。变速箱的油位应保持在油量计的两条线之间。油位过高或过低都会导致各部件温度升高或润滑不良，增加动力损失并导致机器运行不良。

4. The gears and bearings of the reducer of the feeding and mixing machine splash the oil into the inner wall of the oil tank and flow into the bearing for lubrication. The oil level of the gearbox should be maintained between the two lines of the oil gauge. If the oil level is too high or too low, the temperature of each part will rise or the lubrication will be poor, which will increase the power loss and lead to the poor operation of the machine.

5.自动送料搅拌机选用的润滑油应具有一定的粘度和粘温特性，低凝固点，良好的氧化稳定性，无机械杂质和水分，无腐蚀和耐磨材料。其质量指标应符合标准。

5. The lubricating oil selected by the automatic feeding mixer should have certain viscosity and viscosity temperature characteristics, low freezing point, good oxidation stability, no mechanical impurities and moisture, no corrosion and wear-resistant materials. The quality index should meet the national standard.

上料搅拌一体机用于润滑，减少磨损，提高部件的使用寿命。但是，在添加润滑油的过程中需要注意一些事项。新机器应在更初150小时和300小时内更换一次，以测试期间未完全清洁的污垢。工作时，请务必检查油位，并及时添加。

The feeding and mixing machine is used for lubrication, reducing wear and improving the service life of components. However, in the process of adding lubricating oil, we need to pay attention to some matters. The new machine should be replaced once in the first 150 hours and 300 hours to remove dirt that was not completely cleaned during the test. When working, please check the oil level and add it in time.

上料搅拌一体机的配置和操作

Configuration and operation of feeding and mixing machine

上料搅拌一体机的主要相关结构是行走底盘，发动机，液力变矩器，双驱动轴，进料装置，进料斗，卸料斗，延伸卸料斗，框架，搅拌桶和搅拌均特别慢一点。机械，液压系统，电子控制系统，自动供水系统等让我们仔细看看。

The main related structures of the feeding and mixing machine are walking chassis, engine, hydraulic torque converter, double drive shaft, feeding device, feed hopper, discharge hopper, extended discharge hopper, frame, mixing drum and mixing are all slower. Machinery, hydraulic system, electronic control system, automatic water supply system, etc. Let's have a closer look.

1.进水系统可根据称重设置实现自动进水。

1. The water inlet system can automatically feed water according to the weighing setting.

2.搅拌筒的旋转由液压马达通过特殊的行星齿轮驱动，行星齿轮的输出轴可以以恒定的角度摆动，以满足在恶劣路况下搅拌筒的节拍。

2. The rotation of the mixing drum is driven by a hydraulic motor through a special planetary gear. The output shaft of the planetary gear can swing at a constant angle to meet the beat of the mixing drum under bad road conditions.

3.双螺旋叶片设置在上料搅拌一体机的混合滚筒的内壁上，正向旋转进料和混凝土搅拌，反向旋转混凝土在螺旋叶片的向下压力下从出口排出。

3. The double helix blade is set on the inner wall of the mixing drum of the feeding and mixing machine, and the concrete is rotated forward and mixed, and the concrete is discharged from the outlet under the downward pressure of the spiral blade.

4.供应干料，按设计比例自动供给斗臂，动臂油缸和计量料斗。

4. Supply dry materials, automatically supply the bucket arm, boom oil cylinder and metering hopper according to the design proportion.

5.液压系统使用恒功率可变排量活塞泵来减少发动机功率损失。

5. Hydraulic system uses constant power variable displacement piston pump to reduce engine power loss.

6.行驶系统由发动机从变矩器和前后驱动轴驱动到前后轴。变矩器的使用减少了对发动机的影响并延长了发动机的寿命。

6. The driving system is driven from the torque converter and the front and rear drive shafts to the front and rear axles. The use of the torque converter reduces the impact on the engine and extends the life of the engine.