自动搅拌车在试用期间会出现各种各样的问题，那么遇到问题的出现就要赶紧的去处理，如何处理自动搅拌车压力不足的情况？这个问题经常能看到用户咨询，下面来看看吧。

　　Automatic mixer will have a variety of problems during the trial period, so it is necessary to deal with the problems quickly. How to deal with the insufficient pressure of automatic mixer? This is a question you often see users asking, so let's take a look.

　　查看自动搅拌车液压泵是否能输出液压油。如果是新的液压泵，无液压油输出，可能是泵体有铸造缺陷(缩孔、砂眼等)，使吸油腔和压油腔相通，失去压油能力，应及时找厂家更换。若不是新的液压泵，无液压油输出，则可能是泵的转向不对，零件磨损严重或损坏，及时更换。

　　Check whether the hydraulic pump of automatic agitator can output hydraulic oil. If it is a new hydraulic pump, there is no hydraulic oil output, it may be that the pump body has casting defects (shrinkage cavity, trachoma, etc.), so that the oil suction cavity and the oil pressure chamber are connected, and the oil pressure ability is lost. It should be replaced by the manufacturer in time. If it is not a new hydraulic pump, there is no hydraulic oil output, it may be the wrong steering of the pump, serious wear or damage of parts, timely replacement.

　　若自动搅拌车液压泵有油液输出，查看溢流阀工作是否正常。若不正常，则可能是压力油路中的某个阀有污物或其他原因卡住，处于回油位置，致使压力油路与溢流回路短路，也可能是管接头松脱，或处于压力油路中的某些阀泄漏严重，或液压缸、液压马达的密封损坏，严重泄漏。排除方法是拆开有关阀进行清洗，检查密封间隙的大小及各种密封装置，密封装置损坏应更换。

　　If the hydraulic pump of automatic agitator has oil output, check whether the relief valve works normally. If it is not normal, it may be that there is dirt or other reasons in a valve in the pressure oil line stuck in the oil return position, resulting in short circuit between the pressure oil line and the overflow loop, or it may be that the pipe joint is loose, or some valves in the pressure oil line leak seriously, or the seal of the hydraulic cylinder and hydraulic motor is damaged, and serious leakage. The elimination method is to disassemble the relevant valve for cleaning, check the size of the sealing gap and various sealing devices, sealing device damage should be replaced.

　　若水泥自动搅拌车的液压泵输出流量随压力升高而显着减小，且压力达不到规定值，则是由于液压泵磨损后间隙增大所致。排除方法是测定液压泵的容积效率，即可确定该泵是否能继续使用，对磨损严重的零件，应进行修配或更换。

　　If the output flow of the hydraulic pump of the cement automatic mixer decreases significantly with the increase of the pressure, and the pressure cannot reach the specified value, it is due to the increase of the gap after the wear of the hydraulic pump. The elimination method is to determine the volumetric efficiency of the hydraulic pump, to determine whether the pump can continue to use, the wear of serious parts, should be repaired or replaced.

　　自动搅拌车的液压系统能建立正常压力，而某些管路或液压缸(或液压马达)中无压力，则可能是由于管路、小孔或节流阀、换向阀等部位堵塞。此时应逐段检查压力和有无油液通过，找出原因，加以排除。

　　The hydraulic system of the automatic agitator can establish normal pressure, and there is no pressure in some pipelines or hydraulic cylinders (or hydraulic motors), which may be due to blockage of pipelines, small holes or throttle valves, reversing valves and other parts. At this point, the pressure and oil should be checked section by section to find out the cause and eliminate it.

　　如何处理自动搅拌车压力不足的情况？如果遇到自动搅拌车压力不足的情况时，大家可以按照上面介绍的方法来查找原因并。更多内容就来这里www.sdzkjf.cn咨询吧。

　　How to deal with the situation of insufficient pressure of automatic mixing truck? If you encounter insufficient pressure of automatic mixing truck, you can find the cause and solve it according to the method introduced above. For more information, please visit www.sdzkjf.cn.